Port Forwarding Active Webcam on the Netgear DG834G

What is Port Forwarding?

View all Router Screenshots.

Before we can forward ports for ActiveWebCam, we need to figure out what ports ActiveWebCam++ is using. Here is a brief walkthrough on how to do that. Go ahead and open up ActiveWebCam and get into the camera you want to modifies settings.

At the top of the camera's properties page click the Broadcasting link.

There are two things on this page that require forwarding a port. If you have Remote Access enabled, you need to forward the port in the remote accesses section's Port box. You can change the port that is in that box if you like. Please enter the port for Remote Access into the box below. If you are not using Remote Access just leave this box blank.

The HTTP Server is the second thing in Active WebCam that requires port forwarding. The Port box in the Http Server section contains the port number that must be forwarded for the HTTP Server. You can change that port number if you like. Please enter the port you are using for the HTTP Server into the box below. If you are not using the HTTP Server just leave this box blank.

To setup port forwarding on this router your computer needs to have a static ip address.
Try our free PF Setup Static IP Address Program which will setup a static ip address for you.

Or you can take alook at our Static IP Address guide to setup a static ip address. When you are finished setting up a static ip address, please come back to this page and enter the ip address you setup in the Static IP Address box below.

Do not skip this step!

Open a web browser like Internet Explorer or Firefox. Enter the internal IP address of your router in the address bar of your browser. If you do not know your routers internal IP address please read our How To Find Your Routers IP Address guide.

In the picture above the address bar has http://www.google.com in it. Just replace all of that with the internal IP address of your router. By default the IP address should be set to 192.168.0.1.

You should see a box prompting you for your username and password. Enter your username and password now. By default the username is admin, and the password is password. Click the Ok button to log in to your router.

Please visit our Default Router Passwords page if the username and password shown above did not work for you.

We will list a series of lines here that will show you exactly how to forward the ports you need to forward. Active Webcam requires you to forward the ports you entered above. Go ahead and enter the settings shown above into the Virtual Server menu and then click Add.

Under Security in the left hand menu click Services.
You should see the following menu.


Click Add a Custom Service


Go ahead and name your service. It doesn't really matter what the name is, but something easy to remember would be good. Select tcp or udp under type. If you are unsure of the type just select both. Last put in the Start and Finishing port numbers. If the service only requires one port, put that port number in both the start and the finish box. You may need to setup multiple services, depending upon the number of ports/port ranges the software you want to run requires. Click Apply when you have finished. Now we need to go to the second section to continue setting up our port forwarding. Under Security in the left hand menu click Rules.
Once again you should see the following menu.


Go ahead and click Add in the Outbound or Inbound services section. If you are unsure whether the program you are using will use these ports for inbound or outbound traffic, repeat steps 7 through 9 for both Inbound and Outbound.


Select the service we previously created. Action should be set to ALLOW always. Enter the ip address you want to forward these ports to in Send to LAN Server. If you are forwarding ports so you can run a program on your computer, you should enter the your computers ip address into this box. Wan Users should be set to Any, unless you want to limit who you want to connect to these ports. This would be useful, lets say, if you only wanted your office computer to be able to ftp into your home computer. In that case you would put your office computers ip address in both the start and finish box. Generally log should be set to never, unless of course you want to create a log of network activity.
When you are finished with that configuration go ahead and click Apply.

You should see another page of settings that need to be entered into one of the blank lines on your routers Virtual Server page. Go ahead and enter those settings and then click Add.

Under Security in the left hand menu click Services.
You should see the following menu.


Click Add a Custom Service


Go ahead and name your service. It doesn't really matter what the name is, but something easy to remember would be good. Select tcp or udp under type. If you are unsure of the type just select both. Last put in the Start and Finishing port numbers. If the service only requires one port, put that port number in both the start and the finish box. You may need to setup multiple services, depending upon the number of ports/port ranges the software you want to run requires. Click Apply when you have finished. Now we need to go to the second section to continue setting up our port forwarding. Under Security in the left hand menu click Rules.
Once again you should see the following menu.


Go ahead and click Add in the Outbound or Inbound services section. If you are unsure whether the program you are using will use these ports for inbound or outbound traffic, repeat steps 7 through 9 for both Inbound and Outbound.


Select the service we previously created. Action should be set to ALLOW always. Enter the ip address you want to forward these ports to in Send to LAN Server. If you are forwarding ports so you can run a program on your computer, you should enter the your computers ip address into this box. Wan Users should be set to Any, unless you want to limit who you want to connect to these ports. This would be useful, lets say, if you only wanted your office computer to be able to ftp into your home computer. In that case you would put your office computers ip address in both the start and finish box. Generally log should be set to never, unless of course you want to create a log of network activity.
When you are finished with that configuration go ahead and click Apply.

And that is it! You are done!

To test if your port has been properly forwarded, you can use our Port Checker tool.

Didn't find the screenshot you were looking for? Check our our giant collection of router screenshots.