Port Forwarding the Sitecom DC-202 Router for QSee QT428-803
If you don't know what Port Forwarding is yet, you might want to start by reading our What is Port Forwarding guide.
You might also be interested in our huge collection of Router Screenshots where you can
see every page of every router that we know of.
Login to the Sitecom DC-202 Router
Now we need to know your routers IP address. You can find it a variety of ways.
How To Find Your Sitecom DC-202 Router IP Address
It's ok if you don't know your Sitecom DC-202 router's internal IP address. You can find it by doing one of the following:
Login To The Sitecom DC-202 Router Using Your Web Browser
Open a web browser like Internet Explorer or Firefox. Enter the internal IP address of your router in the address bar of your browser.
In the picture above the address bar has http://www.google.com in it. Just replace all of that with the internal IP address of your Sitecom DC-202 router.
By default the IP address should be set to 192.168.0.1.
You should see a box prompting you for your username and password. Enter your username and password now.
The Default Sitecom DC-202 Router Username is: blank
The Default Sitecom DC-202 Router Password is: blank
Click the Ok button to log in to your Sitecom DC-202 router.
Default Usernames and Passwords for other Sitecom Routers
Please visit our Default Sitecom Router Passwords page if the username
and password shown below did not work for you.
If you can't login to your router because you forgot your Sitecom DC-202 router username and password, use our
How to Reset a Router Password guide to set your
Sitecom DC-202 router back to its factory settings.
How to Port Forward QSee QT428-803 on the Sitecom DC-202
Having trouble forwarding ports on the Sitecom DC-202?
If you are having trouble with this guide, then perhaps PFConfig may be your solution.
PFConfig is a software tool that will automatically forward ports for your router to save you time and hassle.
- Go to the Network Menu.
- Put a check into the Obtain an IP Address Automatically box.
- Click the Test button.
- Look near the lower left corner. If it says Ok, then click on Apply, then Exit.
- Go to Menu - Information and Network
- Write down the IP Address, Subnet Mask and Gateway.
- Go back to the Network Menu.
- Uncheck the Obtain an IP Address Automatically box.
- Now enter the IP Address, Gateway and Subnet Mask you wrote down earlier.
- When you're done click Apply, then Exit.
Sitecom DC-202 Router Port Forwarding Screenshots
Now that you are logged in to your Sitecom DC-202 router you should see the following:
Click the Advanced button near the right of the page.
Click the Virtual Servers link near the center of the page.
Forward Ports 80 on the Sitecom DC-202
We will list a series of lines here that will show you exactly how to forward the ports you need to forward. QSee QT428-803 requires
you to forward the 80,6036 ports. Go ahead and enter the settings shown above into the Virtual Servers menu and then click Add as new Server.
Forward Ports 6036 on the Sitecom DC-202
You should see another page of settings that need to be entered into one of the blank lines on your routers Virtual Servers page.
Go ahead and enter those settings and then click Add as new Server.
And that is it! You are done!
Test if Your Ports are Open
Now that you have forwarded ports for QSee QT428-803 on the Sitecom DC-202 you should test to see if your ports are forwarded correctly.
To test if your port has been properly forwarded, you can use our Open Port Check tool.
Our Open Port Check tool is the only online port checking tool with Guaranteed Results.
Sitecom DC-202 Router Screenshot Database
Didn't find the screenshot you were looking for? Check our our
Sitecom DC-202 Router Screenshots.
We have the Internets largest collection of Router Screenshots.